Frequently Asked Questions
How do I choose a KRAKEN ACCESSORIES set?
Choose by whether your rod has a reel and by the rod diameter. Check the set images and specifications before ordering.
Which KLAW version should I choose?
Choose Pegboard for a compatible pegboard, or Screw-mount for a screw-fixed installation.
How much space does KRAKEN PRO need, and how many rods can it hold?
The body is approximately 802 mm tall and 250 mm in diameter, and weighs about 25 kg. Its 18 vertical rails can accommodate up to 18 rods, depending on your accessories and the size of your rods and reels. Allow room around it for rotation and for the full length of your rods.
Can I store a fishing rod with the reel attached?
Yes. The appropriate rod-and-reel accessory set supports compatible rods with spinning or baitcasting reels attached, with a rod diameter of up to 14 mm. Check the fit and weight of your equipment before ordering. KLAW is for storing a reel separately.
Can I adjust the holders or add more accessories later?
Yes. Press and hold the button on top of the component, slide it to the required height, then release the button to lock it. Position the holders to keep the rod upright and clear of its guides. Do not force a holder to slide without pressing the button. Additional compatible accessory sets can be fitted as your collection grows.
How much weight can the holders support, and how should I arrange my gear?
Do not exceed 3 kg on an individual KRAKEN rod-storage component; also follow any lower limit specified for your accessory. KLAW has its own load limits, so the 3 kg figure should not be applied to it. Place the unit on a level, stable surface and distribute equipment evenly around the body. Its low centre of gravity does not make it tip-proof: do not push, lean on or climb it, and keep children from climbing or pulling on it.
How do I turn the light on and change its brightness?
Touch and hold the top wooden panel for about 3 seconds to turn the light on or off. It starts at 75% brightness. Tap the panel to cycle through 100%, breathing mode, 25%, 50% and 75%.
Can I use the light without keeping it plugged in?
Yes. The light can run on its rechargeable battery when charged. Connect power to the socket at the bottom of the body to charge it. A full charge takes approximately 4-5 hours. For first use, connect power first to check operation.
Why will the light not turn on when I first unpack KRAKEN PRO?
The battery may have discharged during transport. Connect power and charge for at least 30 minutes before trying again; the initial glow can be difficult to see in a bright room. A full charge takes approximately 4-5 hours. If it still does not respond, unplug the power, wait about 10 seconds, reconnect it securely, then touch and hold the wooden panel for 3 seconds. If the problem continues, contact support rather than opening the unit.
Why does the light flash three times or pulse while charging?
Three flashes when you try to switch it on indicate an empty battery: connect power to charge it. A breathing or pulsing light while the light is switched off and power is connected is the normal charging indicator. Breathing mode selected while the light is on is a separate lighting setting.
What should I do if the wooden touch panel does not respond?
Wipe the panel with a dry cloth and touch it with a bare finger or your palm. A larger contact area can help; gloves, cold hands and very dry conditions can reduce sensitivity. Warm your hands and hold contact for about 3 seconds. If it still does not respond, check the charge and try the power-reset steps above. Contact support if the issue persists.
Is the mechanical clicking sound during rotation normal?
Yes. The mechanical sound is part of the intended rotation feedback. If rotation becomes stiff or jerky, you feel unusual resistance, or the usual sound disappears, stop using the rotation mechanism and contact support. Do not force it or open the unit.
What should I do if a holder starts to slide down?
Remove the equipment first. Check that the load is within the accessory limit and that the mounting plate is correctly seated and the hex screw is secure, without overtightening it. The replaceable silicone friction pad may be worn. Replace it with a suitable replacement pad and refit the component. If it still slips, stop using that component and contact support.
Will the KLAW Pegboard version fit any pegboard?
No. Check the hole size and spacing against the KLAW product specifications before ordering. IKEA pegboards and pegboards with particularly large square holes are not compatible with this version. Do not force the hooks into holes that do not align. If you are unsure, contact us with your pegboard measurements before ordering.